[GMCnet] Oil cooler line connections [message #349939] |
Thu, 07 November 2019 19:14 |
Gerard Hickey
Messages: 53 Registered: June 2019
Karma: 1
|
Member |
|
|
Good evening,
I have a good one and hopefully will not leave everyone scratching their
heads.
I am replacing the oil cooler lines (just the flex lines) on a 455
engine. On the end of the hard tubes is a flare connection with male
threads and on the end of the flex lines is another flare connection
with female threads. So how does one join these connections together?
I just finished taking some copper washers and adapting them to be used
for a flared fitting. See https://youtu.be/u7WULLs2nV8 to see what I made.
Now that I have more light to work with tonight I started trying to put
everything together and then I realized that both ends were flared I
figure that the copper washer as a flare gasket will not work. Am I wrong?
If both ends were male threads, then It would be a fairly simple trip to
O'Reillys to get a connector that would join both flares together. With
the one end being female threads, that seems to be throwing a wrench
into everything.
Any thoughts?
Thanks.
--
Gerard Hickey / WTØF IRLP:3067/Echolink:529661
hickey@kinetic-compute.com DMR: 3102272
425-395-4554
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|
Re: [GMCnet] Oil cooler line connections [message #349942 is a reply to message #349939] |
Thu, 07 November 2019 20:00 |
jimk
Messages: 6734 Registered: July 2006 Location: Belmont, CA
Karma: 9
|
Senior Member |
|
|
Use a coupler
On Thu, Nov 7, 2019 at 5:15 PM Gerard Hickey via Gmclist <
gmclist@list.gmcnet.org> wrote:
> Good evening,
>
> I have a good one and hopefully will not leave everyone scratching their
> heads.
>
> I am replacing the oil cooler lines (just the flex lines) on a 455
> engine. On the end of the hard tubes is a flare connection with male
> threads and on the end of the flex lines is another flare connection
> with female threads. So how does one join these connections together?
>
> I just finished taking some copper washers and adapting them to be used
> for a flared fitting. See https://youtu.be/u7WULLs2nV8 to see what I made.
>
> Now that I have more light to work with tonight I started trying to put
> everything together and then I realized that both ends were flared I
> figure that the copper washer as a flare gasket will not work. Am I wrong?
>
> If both ends were male threads, then It would be a fairly simple trip to
> O'Reillys to get a connector that would join both flares together. With
> the one end being female threads, that seems to be throwing a wrench
> into everything.
>
> Any thoughts?
>
> Thanks.
>
> --
> Gerard Hickey / WTØF IRLP:3067/Echolink:529661
> hickey@kinetic-compute.com DMR: 3102272
> 425-395-4554
>
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
--
Jim Kanomata
Applied/GMC, Newark,CA
jimk@appliedairfilters.com
http://www.appliedgmcrvparts.com
1-800-752-7502
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Jim Kanomata
Applied/GMC
jimk@appliedairfilters.com
www.appliedgmc.com
1-800-752-7502
|
|
|
Re: [GMCnet] Oil cooler line connections [message #350037 is a reply to message #349939] |
Mon, 11 November 2019 14:41 |
Ken Henderson
Messages: 8726 Registered: March 2004 Location: Americus, GA
Karma: 9
|
Senior Member |
|
|
The YouTube method's simpler & better, but if you can't get copper gaskets,
this can work too (did for me anyway):
http://www.gmcmhphotos.com/photos/g4452-flare-fitting-repair-with-copper-seal.html
Ken H.
On Thu, Nov 7, 2019 at 8:15 PM Gerard Hickey via Gmclist <
gmclist@list.gmcnet.org> wrote:
> Good evening,
>
> I have a good one and hopefully will not leave everyone scratching their
> heads.
>
> I am replacing the oil cooler lines (just the flex lines) on a 455
> engine. On the end of the hard tubes is a flare connection with male
> threads and on the end of the flex lines is another flare connection
> with female threads. So how does one join these connections together?
>
> I just finished taking some copper washers and adapting them to be used
> for a flared fitting. See https://youtu.be/u7WULLs2nV8 to see what I made.
>
> Now that I have more light to work with tonight I started trying to put
> everything together and then I realized that both ends were flared I
> figure that the copper washer as a flare gasket will not work. Am I wrong?
>
> If both ends were male threads, then It would be a fairly simple trip to
> O'Reillys to get a connector that would join both flares together. With
> the one end being female threads, that seems to be throwing a wrench
> into everything.
>
> Any thoughts?
>
> Thanks.
>
> --
> Gerard Hickey / WTØF IRLP:3067/Echolink:529661
> hickey@kinetic-compute.com DMR: 3102272
> 425-395-4554
>
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Ken Henderson
Americus, GA
www.gmcwipersetc.com
Large Wiring Diagrams
76 X-Birchaven
76 X-Palm Beach
|
|
|
|
|
|
Re: [GMCnet] Oil cooler line connections [message #350052 is a reply to message #350051] |
Tue, 12 November 2019 11:24 |
Richard Denney
Messages: 920 Registered: April 2010
Karma: 9
|
Senior Member |
|
|
And if it isn’t soft enough, just anneal it with a torch.
Rick “the flare tool will harden it” Denney
On Tue, Nov 12, 2019 at 11:25 AM Emery Stora via Gmclist <
gmclist@list.gmcnet.org> wrote:
> Matt
> I had bought the Harbor Freight assortment and used my flare tool to make
> a flat washer into a conical one. It then worked fine in an inversed flare
> fitting.
>
> Emery Stora
>
>> On Nov 12, 2019, at 7:05 AM, Matt Colie via Gmclist gmclist@list.gmcnet.org> wrote:
>>
>> Jp Benson wrote on Mon, 11 November 2019 21:02
>>> Harbor Freight sells an assortment of copper washers.
>>> https://www.harborfreight.com/search?q=copper%20washer%20assortment
>>> JP
>>
>> JP,
>> Those aren't flare washers and the ones I got were alright for diesel
> banjo fittings, but were too hard to put in an SAE flare.
>> Matt
>> --
>> Matt & Mary Colie - '73 Glacier 23 - Members GMCMI, GMCGL, GMCES
>> Electronically Controlled Quiet Engine Cooling Fan
>> OE Rear Drum Brakes with Applied Control Arms
>> SE Michigan - Twixt A2 and Detroit
>>
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
--
'73 X-Glacier 230 "Jaws"
Northern Virginia
Offlist email: rick at rickdenney dot com
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|
|